{"id":1310,"date":"2013-12-12T16:01:01","date_gmt":"2013-12-12T16:01:01","guid":{"rendered":"https:\/\/www.4ward4x4.com\/?p=1310"},"modified":"2020-06-16T17:19:34","modified_gmt":"2020-06-16T17:19:34","slug":"assembly-instructions-engage4x4-roof-rack-system","status":"publish","type":"post","link":"https:\/\/www.4ward4x4.com\/en\/assembly-instructions-engage4x4-roof-rack-system\/","title":{"rendered":"Assembly instructions ENGAGE4X4 roof rack system"},"content":{"rendered":"

ENGAGE4X4 roof rack with Airline sytsem – Installation instructions<\/span><\/h2>\n

Bill of material fittings (may vary according to roof rack length)<\/span><\/em><\/p>\n

ENGAGE4X4 roof rack parts<\/span><\/strong><\/span><\/p>\n

    \n
  • 2 side sections with 120 mm radius<\/span><\/li>\n
  • 2 side profiles<\/span><\/li>\n
  • 5 to 13 cross braces (depending on roof rack length)<\/span><\/li>\n
  • 4 countersunk screws M6X20 per cross brace<\/span><\/li>\n
  • 4 hoods – V4A<\/span><\/li>\n
  • 8 screws M6X25 pan head (for reinforcing sheet)<\/span><\/li>\n
  • 4 sleeve nuts per cross braces<\/span><\/li>\n<\/ul>\n

    ENGAGE4X4 roof rack feet (vehicle access)<\/span><\/strong><\/p>\n

    Foot Type : 5V1 to 3 series (height variable)<\/span><\/em><\/p>\n

      \n
    • 1 roof carrier support sheet<\/span><\/li>\n
    • 1 roof rack access channel<\/span><\/li>\n
    • 1 clamping plate roof rack<\/span><\/li>\n
    • 2 screws M8X20 hex with locking teeth (height adjustable connection)<\/span><\/li>\n
    • 2 screws M8X15 hex (leading foot to carrier)<\/span><\/li>\n
    • 2 nuts M8<\/span><\/li>\n
    • 1 screw M8X20 Hexagon socket button head (clamping plate gutter)<\/span><\/li>\n<\/ul>\n

      Tools<\/span><\/strong><\/span><\/p>\n

        \n
      • Allen key 4, 5 and 6 mm<\/span><\/li>\n
      • Plastic hammer<\/span><\/li>\n
      • Wrench 13 mm<\/span><\/li>\n<\/ul>\n

        Installation instructions for ENGAGE4X4 roof rack<\/span><\/strong><\/span><\/p>\n

          \n
        1. Insert the front part and the side parts in the form of the support on a suitable work surface (with a pad to protect from scratches).<\/span><\/li>\n
        2. Connect two cross braces to the reinforcement as well as the front and side parts of the roof rack with each other (here the M6X25 pan-head screws are used).<\/span><\/li>\n
        3. Now run cross brace for cross brace in the side profiles and position the cross braces with the matching holes in the side profiles.<\/span><\/li>\n
        4. Now put the sleeve nuts from the bottom and make sure that the side with the reduction is up.<\/span><\/li>\n
        5. Then replace gradually all countersunk screws (M6X20) to loose. <\/span><\/li>\n
        6. At the reinforcing plates using the eight supplied pan-head screws (M6X25).
          \n<\/span>The tolerances of the roof rack are very low in order to ensure that the highest stability can.<\/span><\/li>\n<\/ol>\n

          Tip: To prepare the sleeve nut , you can use a Phillips screwdriver to bring the connecting parts in the correct position.<\/span><\/em><\/strong><\/p>\n

          A montage video of the roof rack can be found here here<\/strong><\/span><\/a>.
          \n<\/span><\/p>\n<\/div><\/section>\n